A2 Ethernet Dock
The A2 Ethernet Dock is a mounting station for the Archer 2
and Allegro 2 Rugged Handhelds. It provides an ethernet port
for networking, power input jack, and USB client port.
Ethernet Specications
10/100 Mbps twisted-pair ethernet
IEEE802.3 10Base-T / 100Base-TX
Manages twisted pair crossover detection and correction
Supports full-duplex and half-duplex
Ethernet driver software pre-installed on the handheld
Dock Features
Accessories
Included with the Dock
USB cable (USB-A to USB-B)
Archer 2 insert and two screws
Accessories Available Separately
12VDC charger that came with the handheld
Communication software like ActiveSync
®
or Mobile
Device Center
®
to allow communication between the
handheld and the host computer (free from Microsoft’s
website)
Docking I/O module for the handheld if it is not factory
installed (available from Juniper Systems or your dealer)
CAT5 or CAT6 twisted-pair ethernet cable
Communication software to communicate with the
handheld over an ethernet network (options include
custom software or programs from a third party vendor
such as Soti MobiControl, www.soti.net/mobicontrol or
AirWatch, www.air-watch.com)
Two #6-32 screws to mount the dock to a surface (optional)
Using the Ethernet Dock
1. The ethernet dock is a freestanding desktop base. It can
also be mounted to a horizontal surface like a desk or
shelf. To mount the dock, drill two holes 4-5/8”apart
through the mounting surface. Screw two #6-32 screws up
into the threaded holes in the dock’s boom base plate.
1 Handheld backrest and connector protector slot
2 LED Indicator: is on when the dock has power
3 Docking pins
4 Archer 2 insert
5 Power input jack: 12VDC power input to power the Ethernet
dock and the handheld.
6 Ethernet port: for networking using an ethernet cable and
software. LED indicators on port:
- Yellow LED indicates a speed of 100 Mbps
- Green LED indicates that there is data activity
7 USB client port: for connection to the host computer
5 6 7
2
1
4
3
2. The handheld must have a docking I/O module. The
lower right side of the module has docking pin contacts as
shown below:
If you have a standard I/O module, replace it with a
docking I/O module. Follow the instructions included
with the kit.
3. To use an Archer 2 with the dock, install the insert as
shown below. This step is not required for the Allegro 2.
4. Provide power to the dock and charge the handheld
baeries using the 12VDC charger that came with your
handheld.
5. If the handheld has a connector protector, open it to
reveal the connector ports. Pull it back as shown below.
6. Hold the handheld so the connector ports are at the
boom and the keypad is facing forward. Insert the
handheld into the dock as shown below. Align the
docking pins on the dock with the contacts on the
handheld I/O module. The handheld automatically turns
on.
7. For networking, use an ethernet cable to connect the dock
to an ethernet switch or to an internal network.
8. Use communication software to communicate with
the handheld over an ethernet network. Follow the
instructions included with the software.
9. You can communicate with the host computer by
aaching the USB cable to the dock and the computer.
Install communication software like ActiveSync on the
computer. Power must be applied to the dock to use USB.
10.
Insert your handheld into the dock, make sure it is
charging, and leave it. Synchronization automatically
occurs.
11. The handheld can be used when it is in the dock. The
keys are all accessible.
Note: Do not have both the USB and ethernet connected to the
handheld at the same time. The communication software will not
know which connection it should communicate through.
(2 pages)
(102 pages)
(96 pages)
(106 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals